HOME
PRODUCTÂ
All Categories
Tapping machine
Non-standard custom Drilling Machine
Gantry Machine Center
Vertical Machine Center
Drilling and tapping machining center
CNC lathe
ABOUT US
SOLUTION
NEWS
FACEBOOK
CONTACT US
All Categories - Hoporo Machinery
All
Tapping machine
Non-standard custom Drilling Machine
CNC lathe
Drilling and tapping machining center
Gantry Machine Center
Vertical Machine Center
M14-M20 Fully automatic four-axis standard tapping machine
Tapping range : M14-M20 Productivity:40-80 pcs/min Total power: 10kw Air pressure: 0.6mp
M6-M12 Fully automatic four-axis standard tapping machine
Tapping range : M6-M12 Productivity:60-120 pcs/min Total power: 11.5kw Air pressure: 0.4-0.5mp
M6-M12 Special-shaped nut fully automatic four-axis tapping machine
Tapping range : M6-M12 Productivity:60-160 pcs/min Total power: 6kw Air pressure: 0.5-0.6mp
M6-M12 Fully automatic intelligent four-axis tapping machine
1. When the rear discharge door of this machine is opened, the spindle will not be able to start. This is to prevent the operator from getting injured during abnormal startup. 2. This machine has an abnormal alarm prompt. The fault code will be displayed on the touch screen, facilitating the operator's troubleshooting. 3. This machine is equipped with torque monitoring and nut status monitoring. 4. This machine is equipped with two sets of oil sludge separators. They can effectively separate the tap oil and waste chips, preventing the waste chips from entering the oil tank and avoiding the wear of the tap and the deterioration of the surface finish of the nuts. 5. This machine is equipped with a defective product sorting mechanism. When there is abnormal torque, the number of nuts set at the front and rear of this mechanism will not stop and will flow into the defective product transfer box continuously. (The rear discharge of this machine is equipped with two independent discharge outlets and one defective product discharge outlet.)
Two axis tapping machine with outer frame
Configuration instructions: 1.92Sf dual servo head 2. Spindle servo motor 3.0KW 3. Feed servo motor 1.0KW 4. Splitter synchronous drive 5. Hydraulic clamping 6. Kunlun mode touch screen operation 7. Remote assistance 8.D520 vibration disk 9. Delta PLC control 10. Maximum speed: 1800r/min
Single spindle tapping machine without frame
Configuration instructions: 1.74# Dual servo tapping head 2. Touch screen operation 3. Remote assistance, can download or change the program 4.PLC control system 5. Pneumatic direct push clamping 6. Vibrating disk automatic feeding 7. Precision divider servo motor synchronous drive 8. Large hole, small hole, no material alarm function 9. Maximum speed: 3000r/min
Two axis tapping machine without outer frame
Configuration instructions: 1.92Sf dual servo head 2. Spindle servo motor 3.0KW 3. Feed servo motor 1.0KW 4. Splitter synchronous drive 5. Hydraulic clamping 6. Kunlun mode touch screen operation 7. Remote assistance 8.D520 vibration disk 9. Delta PLC control 10. Maximum speed: 1800r/min
Single axis tapping machine with outer frame
Configuration instructions: 1.74# Dual servo tapping head 2. Touch screen operation 3. Remote assistance, can download or change the program 4.PLC control system 5. Pneumatic direct push clamping 6. Vibrating disk automatic feeding 7. Precision divider servo motor synchronous drive 8. Large hole, small hole, no material alarm function 9. Maximum speed: 3000r/min
Image recognition screening press machine
Supported number of cameras: 1-16 Detection speed: up to 1200pcs/min Detection accuracy: up to 0.002mm Recommended minimum graphics card: RTX2060 or above
Nut threading machine and pressing machine
Tapping range : M6-M12 Productivity:20-50 pcs/min Total power: 1.5kw Air pressure: 0.4-0.5mp
Nut threading machine and pressing machine 1
Tapping range : M6-M12 Productivity:30-60 pcs/min Total power: 1.5kw Air pressure: 0.4-0.5mp
Non-standard customization automatic copper block drilling and chamfering machine
The efficiency can complete 3-5 workpieces per minute and 180-300 workpieces per hour.
Non-standard customization full automatic large thread double axis tapping machine
The efficiency can complete 20 workpieces per minute and 1200 workpieces per hour.
Non-standard customization automatic three-axis multi-head tapping machine
The efficiency can complete 30 workpieces per minute and 1800 workpieces per hour.
Non-standard customization tiger card automatic tapping double chamfering machine
The efficiency can complete 10 workpieces per minute and 600 workpieces per hour.
Non-standard customization automatic assembly machine for shaped nail
The efficiency can complete 12 workpieces per minute and 720 workpieces per hour.
Non-standard customization fully automatic tapping + screwing machine
The efficiency can complete 10-12workpieces per minute and 600-720 workpieces per hour.
Automatic tapping and chamfering machine non-standard customization
The efficiency can complete 10 workpieces per minute and 600 workpieces per hour.
Automatic punching machine non-standard customization
The efficiency can reach about 20 workpieces per minute.
ZMLF-1690 High precision vertical machining center
X/Y/Z Travel: 1650/900/900mm Table size: 1700*850mm Max. load of the table: 1600kg ATC content: 24
Show more
HOPORO MACHINERY
PRODUCT
All
Tapping machine
Non-standard custom Drilling Machine
CNC lathe
Drilling and tapping machining center
Gantry Machine Center
Vertical Machine Center
Load More
WhatsApp
Email
Cookie Use
We use cookies to ensure a smooth browsing experience. By continuing we assume you accept the use of cookies.
Accept
Learn More
